Make sure your z-offset is set correctly, the first layer should have some ”squish” as it is layed down, while still leaving room for filament to flow out of the nozzle.Clean the bed with dish soap and warm water as detailed in the bed installation guide.Ensure that your bed temperature is set to 60℃.You may also take a look at our Troubleshooting Page for any additional issues you may encounter.
For more advanced support, please join our community Discord server. This guide will help with basic troubleshooting.
If you are not getting optimal finish, bed adhesion or part release, it’s likely to be an issue associated with your printing parameters. Then, lower your Z axis to 0 and again slide a piece of paper under the nozzle, feeling for the same resistance as before.ĪLWAYS check that print bed is level and z-offset is calibrated before attempting to print any parts.
To ensure a proper calibration, home your printer using the G28 command or the LCD controls. Save new z-offset settings to EEPROM by clicking “Store settings”. ADJUST Z-OFFSET setting until at Z = 0, you feel friction while sliding the paper between the nozzle and print bed. If your nozzle touches the paper before Z = 0, then increase your z-offset, home XYZ and try again. If the nozzle cannot touch the paper even when Z = 0, decrease your z-offset in 0.5mm increments, home XYZ and try again.ī. USING LCD SCREEN, gradually move the nozzle to Z = 0.Ī. CENTER NOZZLE above middle of print bed. HEAT THE PRINT BED to 60☌, it is important that the hotend remains cool. USE EXTREME CAUTION TO AVOID SCRATCHING THE VAAPR BED. Take care not to scratch the build plate when moving from one corner to another. REPEAT STEPS 3 and 4 for each of the other 3 corners. ADJUST BED LEVELLING screws until you can feel friction while sliding the paper between the nozzle and print bed. MOVE NOZZLE TO ONE CORNER of build plate. HEAT PRINT BED to 60☌, it is important that the hotend remains cool.Ī. Once adjusted, rotate all four leveling wheels three revolutions counterclockwise, lowering the bed to prevent scratching. If not using auto levelling you will need to lower the Z-endstop switch so that the nozzle gently touches the bed when activated. If using auto levelling ensure your probe reliably triggers before attempting to level the bed. Make sure your nozzle is clean and cool before proceeding. If you are unsure, please contact 3DQue through the community Discord channel or EXTREME CAUTION TO AVOID SCRATCHING THE VAAPR BED.Ī nozzle scraping the bed will cause permanent damage. Incorrect firmware or slicing settings for your printer configuration may pose a hazard. Follow all manufacturers instructions and safety measures which may include not leaving the printer unattended without appropriate safety features in place. WARNING: 3D printers have heated elements that pose a fire risk. We provide firmware options for Inductive Probes and BL Touch. To get even better quality from your printer, we recommend installing an automatic bed-leveling system before using this product. So please, set Quinly up for success - read this manual, follow the instructions carefully, and if you have any questions, contact us at or post them in our community Discord channel (). Quinly’s purpose is to make your life easier by saving you hours of scraping, taping, flexing, removing parts, scheduling jobs, and generally having to babysit your printer. #ENDER 3 SD CARD SLOT NOT WORKING MANUAL#
Follow this manual carefully and Quinly will save you hundreds of hours scheduling jobs, uploading files, running prints, and removing parts. These actions will damage the VAAPR print bed and Quinly will not work properly.
DO NOT USE adhesives, solvents, scrapers. Quinly automation is enabled by the VAAPR™ print bed which is the first surface for 3D printers offering variable adhesion - high first-layer adhesion when hot, and no first-layer adhesion when it’s cold. If you are unsure about compatibility please contact us. Quinly is also compatible with a variety of modifications. Quinly can run a well-calibrated, properly maintained 3D printer continuously until it runs out of filament. Quinly works day and night, evenings and weekends, so you don’t have to. Thank you for purchasing the Quinly for Ender 3, an automated print management system compatible with Ender 3, Ender 3 Pro, and Ender 3 V2 3D printers.
0 kommentar(er)
